The Good, The Bad, The Remington R51

So I am sure by now many of you have seen the multitude of posts that have been floating around the web about the Remington R5, it almost seems like every one of the guns that was sent out had some sort of issue. Sadly for a gun that had so much hype both by Remington and the gun community it is sad to see just how poorly the adaptation of the R51 has done in 9mm.



In this post I wanted to write down some of my thoughts on the gun, while this is not a glowing review it is also not a "You should never buy a Remington R51" post, so please stick with me to the end to understand exactly what I mean by that.

I personally had been looking forward to getting my hands on one of these after seeing the display models they had at SHOT Show. The ergonomics and the way that the gun fit in my hand made it interesting to me. While it may look like some weird futuristic ray gun you would see in a sic-fi movie it does have a comfortable feel to it.

The review pistol that I received showed up to my FFL back in March and I was looking forward to picking it up despite the fact that a few other people had received some that were less than acceptable. When I opened up the box and picked the gun up I noticed that it felt a bit rough, albeit a little unrefined, nothing like the copies I had seen at SHOT.  When I first racked the slide back I cringed a bit at how gritty and rough the slide felt, but I blamed part of that on factory lubrication (or lack there of) and was wondering how much that would change once I had it stripped down and properly lubricated.  One of the other things that I noticed was how spongy the trigger pull was, and how the reset literally required me to move my finger all the way forward before it was ready for the next shot.

When I got the pistol home I took the directions out of the box (yes I use directions) to figure out how to take the gun down since I had never taken one down before and it does require a unique technique. The first thing I noticed was how hard the slide release pin was to get out, and when I say hard I mean I had to actually take a punch to it. Once the pin was out I started the hop on one foot, rolling my eyes, while sticking my tongue out, and pulling the barrel while keeping the slide pulled back take down process (it's really not that hard after you figure it out, but seriously?).  I broke the gun down as far as I figured it needed to go and stripped off all of the factory lubrication and applied FIREClean to everything. Once I had the gun put back together I tried racking the slide again, while it was not as gritty as it had been at the shop it was still very rough; almost like it was catching or rubbing on something it shouldn't be.

After messing with the gun a bit more I was comfortable enough to take it out to the range and give it a go, I loaded up the 2 magazines that come with it (115gr FMJ) and fired my first few shots out of it. To say it was a comfortable first few shots would be lying to you, the amount of snap that this little 9mm had was unbelievable, add on top that there was an issue with what felt like slide bite I was completely caught off guard by how uncomfortable it was to shoot. I ran quite a few more mags worth of ammo through the gun, including some hollow point rounds (which fed just fine), but I just couldn't understand why I felt like I was getting slide bite from the gun.

When I got back from the range and watched some of the video I had taken while shooting I noticed that at no time was my hand close enough to be hit by the slide, so that left the question as to what was causing the bite. After taking a little more time to figure out what the biting was caused by I noticed that the back "safety" was actually the cause of the pinch. Instead of being smooth the edges are on the rough side, it also moves back and forth quite a bit while firing; and since there are gaps along the sides and the top to allow for it to function the meat of your hand is pinched by it leaving you with the feeling of slide bite. This is something I would like to see fixed if they bring out a second generation of the R51, along with other modifications that need to be made.

I didn't clean the gun up between the first and second trip out to the range because I wanted to see how the gun would handle not being cleaned between trips and using dirty ammo. I used Tulammo during the second range trip because I know that it is typically some of the dirtiest ammo I can get my hands on. After running around 300 rounds of ammo (100 Tula, 175 federal, 25 HP) it was still functioning but was becoming harder to rack the slide and have it go into battery from slide lock. It was also becoming harder to rack the slide from the closed position. Again it was as if the slide was dragging across something in the process and making it very difficult to move.

Before taking it out for the last range trip and final video I took the gun apart again to look and see if I could figure out what the issue was with the slide being so hard to rack. What I found was the part that goes over the barrel and holds the spring in place had some deep scratches in it from the slide moving over it.

After giving it a closer look it seems like this is where the biggest issue was at as far as slide function went. It is almost as if the tolerances aren't right and the two parts are working against each other and creating friction rather than just allowing proper function. This is something that needs to be fixed, even if it requires going back to the drawing board for Remington.

Is this a design that Remington can salvage and make something much better in a second generation? Yes I believe it is, I think if they fix the slide grinding issue, safety biting issue, and the loose sights issue (not something I had a problem with but have seen others have this problem), they could have a somewhat solid seller. Sure the trigger is not that great but there are innovative people out there who would take advantage of the poor trigger and make something better.

Is the R51 something I would suggest right now? No, the issues I had with my review copy were enough to push me away from the first generation release. With that being said if those issues were fixed and they figured out a way to tame down the amount of flip from recoil I would be more than willing to get my hands on another one and run some rounds down range with it.

This is a gun I will be keeping an eye on as Remington works to make it better (let's hope that they continue to work and listen to the consumer), it still has a look that I have grown to like and it was comfortable in my hand (when I wasn't shooting it). I personally never like to see a product fail because a company decided to rush it out, and then not make improvements when it is shown that the rushed out version has many flaws; so I hope that this design will be turned around and improved instead of failing all together.

Initial Thoughts: Bobster Alpha Goggles and Prowler Deluxe Glasses

(Alpha Goggles)

Recently I began looking into playing airsoft with a few of the guys that I work with and realized that I was going to need a good set of goggles to protect my eyes better than the normal safety glasses I would wear to the range. I remembered seeing the Bobster Alpha goggles during SHOT Show and the fact that their pricing is among a normal persons budget intrigued me. 

So I hit up their site and started checking out the different types of safety goggles and glasses they had available. There were 2 pairs that I found that should work great with the metal mesh masks that I will be using during game play (don't need to lose a tooth to a bb haha). The first pair are the Bobster Alpha goggles, and the second pair are the Prowler Deluxe. Both pairs provide awesome coverage of the eyes while both being ballistically rated, and come with both clear and tinted lenses.

(Prowler Deluxe)

The clarity of the lenses, and the total viewing area on both pair of the glasses is very impressive. The Alpha goggles give an almost completely unobstructed view compared to some of the other goggles I have tried on. The Prowler's also have a great viewing area and are a bit more comfortable to wear since they do not sit on your face like goggles do.

Both pairs are comfortable, however neither pair are something I would wear outside of the airsoft play area. However one of the guys that I work with has deployed with his Infantry unit and when he tried on the Alphas he said he would take them over the ones he was issued any day.

I am really looking forward to using both sets over the next few months and seeing how well they perform. I know a few of the guys have had issues with their goggles fogging up during games, especially since gameplay is all indoors. 

Specs from Bobster

• 
  
• Alpha Goggles:
• Frame Color : Black
• Frame Convertible : No
• Frame Finish : Matte
• Frame RX Ready : Yes
• Frame Temples : N/A
• Warranty : Lifetime against Manufacturing Defects
• Lenses Interchangeable : Yes
• Frame Foam Type : Anti-microbial foam
• Frame Material : Soft Rubber
• Lens Coatings : Anti-fog, 100% UV Protection
• Lens Color : 2 Sets: Anti-fog smoked & anti-fog clear
• Lens Material : 2.5mm Polycarbonate
• Lens Upgrades : Coming soon
• Other included Accessories : 2 Sets of Lenses (Anti-fog Smoked & Anti-fog Clear), Fire Retardant Anti-reflective Sleeve, Microfiber Pouch, MOLLE Carry Case
• Rx Limitation : +/- 10
• Special Features : Fits well under ballistic helmets, Fire retardant strap and anti-reflective sleeve
• Standards Met : ANSI Z87.1-2003 +, MCEPS/ Military Ballistics Impact Standards, CE EN166
• Storage : MOLLE Carry Case

      Prowler Deluxe:

      PROWLER BALLISTICS EYEWEAR, Z87 & MIL-PRF, BLACK FRAME

Pursue superiority with this ANSI Z87.1-2003+ eyewear made of black, military grade nylon frame. The Prowler® offers maximum versatility with removable temples and goggle strap for quick conversion and side shields add strength against flying debris. The Prowler® eyewear system includes an anti-fog smoked lens which exceeds the impact requirements of the stringent military ballistics test, MIL-PRF-31013. The open cell foam absorbs perspiration while a microfiber carry pouch is included.

Glock 42 First Range Trip Thoughts

Today I took the Glock 42 out to the range for a quick session, although I wasn't able to get video due to the wind being strong enough to blow the tripod over I was able to get some decent trigger time. 

One of the biggest things I have been hearing from people is how Glock screwed up by making it a .380 and also making it the size it is (too big) for a .380, while I personally would have prefered it in a 9mm single stack the .380 is still a decent round.

Let me start off with this, for those who complain that it is too large for a .380 handgun there is a point of diminishing returns when it comes to the size of a handgun. When you get so small like the Ruger LCP or the Kahr .380, you get to a point that the gun is no longer comfortable to shoot, and when a gun becomes uncomfortable to shoot you don't train with it. 

In my opinion the Glock 42 is the exact size that it needs to be, it disappears when I carry it appendix IWB and I myself hardly realize it's there. Sure it is a little big to be a pocket pistol, but I have to wonder if it would be practical to draw from your pocket anyways. 

I think the fact that Glock made it the size they did is great, as I said before it is very comfortable to both carry and shoot. I am confident I would have no issue taking a class with it (as long as I could find enough mags). 

This range trip I ran 107 rounds of ammo through it, 7 were PDX1 Self Defense rounds, 50 were PPU 95gr FMJ, and 50 were Remington 95gr FMJ. There were no issues with feeding or firing, the only issue I ran into was the slide not locking back on empty. While it wouldn't lock back on empty with both hands it would lock back with one hand, so I'm thinking it's an issue with hand placement and I will need to work on that.

The 42 was an absolute pleasure to shoot and I was fairly accurate with it also. With the gun being the size it is, it will take me another trip to get it zeroed in. I am looking forward to running quite a few hundred rounds through this gun, and hopefully this next trip out I can actually get some video. 

Make sure to subscribe to the email list to receive the latest updates from the blog, there will be plenty going up over the next few weeks.

Quick Look: Infidel Body Armor

Awhile back we did some on camera shooting of the EnGarde Body Armor  Level III and IV Plates, we were new to doing reviews at the time and learned a lot. Well now we have the opportunity to run another test on a body armor plate thanks to Infidel Body Armor, they sent us one of their 10x12 Plates to use for test and eval.

The last time we did a body armor test we set the plates against a back stop, while that did give us a good idea of what the trauma would be like behind the plate we really couldn't see just how much. This time we are planning on setting blocks of clay behind the plate so we can get a good idea of just how much force is transferred rearward. We will also be checking for spalling since this plate is made of 1/4" AR500 steel with an anti spalling material layered over it.

Just some quick facts about the Infidel Body Armor plates, they are as stated above made from 1/4" AR500 steel and lined with 1/4" of anti spalling material. They are curved so they fit comfortably against the body, and the angled cut makes it easy to shoulder your rifle without setting it on the plate. Each plate weighs a little under 9 pounds, and is rated as a Level III Stand Alone plate.

We are really looking forward to getting some testing time with this plate and are excited to relay the information back to you our viewers. Make sure to check back for the written review and the video soon.

Quick Look: Kaw Valley Precision Linear Comp

Since we here at SpartanTC Reviews have been checking out so many different compensators over the past couple months we figured we would get our hands on a couple more to try out. Recently we contacted Kaw Valley Precision about their Linear Compensator, it was one that a few of you had asked about it, and I had actually seen it a few times while browsing around the internet. KVP was awesomely quick to get back with us and help get our hands on one to test out.

(The new SpartanTC Reviews AR outfitted with the Kaw Valley Precision Linear Comp)

For those who do not know what a linear compensator is here is an answer taken directly from KVP's website.

What is a Linear Compensator? 

A linear compensator is a muzzle device designed to collect and direct all the muzzle gases forward, away from the shooter.  Unlike other types of muzzle devices, KVP linear comps actually lower the decibel the shooter experiences while shooting the rifle. This lowered perceived decibel is especially noticeable in shorter barreled rifles while shooting high power rounds. 

When you first pick up the KVP Linear Comp you can tell right away that it is a solid piece of work, and won't be damaged easily. The machining is really clean on it, and the finish is really well done and seems like it will stand up to quite a bit of abuse.

If you take a close look at the KVP Linear Comp you will notice that the only holes that it has are pointing forward. While this gives it a very different look I am really looking forward to taking it out to the range and seeing how much "quieter" it is over the other comps we have used.

We are hoping to get the new SpartanTC Reviews Test AR out to the range very soon and get some video, along with our initial thoughts on shooting with this comp. Make sure to stay to keep checking back as there are lots of reviews in the works!

Strike Industries J-Comp

I recently had the opportunity to take the Strike Industries J-Comp out to the range and get some shooting in with it. I decided I would write down some of my initial thoughts on it before we head out to the range to do some more shooting with it.

 (Left to Right- 556 Tactical Stryker Comp, Strike Industries J-Comp, 556 Tactical StrykeHyde)

As you can see in the picture above the overall length of the SI J-Comp is slightly longer than the other two muzzle devices, however when it's installed it doesn't look awkward like some other comps I have used before.

One of the first things that you notice about it is the interesting design. It was designed after the Japanese Type 89 Assault Rifle muzzle device, so it is a unique comp to say the least.

The rear two ports are meant to reduce recoil and redirect the concussive force you get from a typical compensator, and the front ports are meant to reduce muzzle flash. This means that it should be the best of both worlds when it comes to reducing recoil while still aiding with hiding the flash. 

The reduction in the concussive force from my experience is not as good as some of the more expensive comps (such as the Lantac Dragon) but at the price point of $39.99 it does a decent job. It does create a dust signature to the sides of the muzzle when shooting prone but the amount of dust created isn't all that bad.

As far as reducing muzzle rise goes the J-Comp does a fair job, while I haven't tried shooting rapidly with it yet the comp does a pretty good job of controlling muzzle rise and allows you to get back on target quickly.

So far with the limited time I have spent with it I am not completely sold on it to the point that I would install it on all of my rifles. It is however well priced and a very well machined compensator, which does what it is advertised to do. Hopefully I will get the opportunity soon to take it out for some night shooting and we can see how well it hides the flash.

Make sure to check back for updates in the near future.

ThinkFast Holsters IWB and Mag Pouch

Around a month ago I received my IWB holster and Double Mag Pouch from ThinkFast Holsters. With as often as I go through guns I had decided to hold off on ordering one for the Glock 19 until I was sure it was going to stick around. I have dealt with several different Kydex holster makers over the past year and a half, so I know what I like and what I don't like. 

The IWB holster and the Double Mag Pouch from ThinkFast are both great quality works of Kydex and there is a great deal of pride that is put into making them.

The IWB holster is comfortable in the appendix position for an extended period of time, even during the 16 hours I wore it during Combat Focus Shooting last weekend. With the sweat guard being a lower cut than some of the other in waistband holsters I have had, I've noticed that it doesn't poke me in the spare tire and make me wish I had worn on OWB holster instead. At the same time the sweat guard is still tall enough to help keep my undershirt from being caught between the gun and the holster (not 100% of the time though).

As you can see in the top 2 pictures the mounting hardware for the loops has been set back and away to keep from doing any damage to your gun while drawing or holstering. This is a feature that I appreciate since my Glock is "fancy".

The soft loops are now my favorite type of loops for an IWB holster, j-hooks are nice but I like the way the soft loops completely lock around the belt versus just sitting behind and under like j-hooks.

.

ThinkFast does a great job of making sure that all edges that come in contact with your body have been smoothed and rounded. When carrying appendix style I don't feel the holster jabbing me in my leg, which is a big plus

The double mag pouch is also very well made, it sits closely to the body making it easy to conceal. Having the center screw for adjusting the amount of retention is a nice touch, I have other mag pouches that do not have this and the mags tend to stick in them since they are a bit of a tight fit.

The loops on the mag pouch are awesome! They are injection molded and are solid. I've snagged the holster a couple times on doorways and such and felt the holster give a good tug on my belt, where other pouches with Kydex formed into loops possibly would have broken.

One thing I have noticed however is that the screws have loosened up a couple times, it's not a big issue as I expected there would always be some small maintenance that would need to be done to any holster that uses screws for mounting.

Overall the mag pouch and IWB holsters are great, I'm sure they will both give me a long life of service. Also an added plus is that the customer service with ThinkFast Holsters is great, and they are quick to answer any questions you may have.

I highly suggest if your looking for a great holster to take a look at what ThinkFast has to offer.

EPLowers Polymer Lower

A few weeks ago I had talked with Chris from www.EPLowers.com about the 80% polymer lowers that they are producing, he was really informative and helpful. He was awesome enough to engrave the SpartanTC81 logo into the lower, which made this already cool project even better in my eyes.

The reason that the EP Lowers can be finished using a Dremel and a drill, is that the firing control group pocket contains a white polymer. The idea behind it is to remove all of the white polymer from inside the pocket until you get to the solid black (or whichever color your lower is). Once you get to the solid color you will still have to remove some of the colored polymer to allow for the proper fit of the firing control group.

In the picture above you can see a good majority of the white polymer has been removed. Notice the black "bars" that are on the sides, these help you gauge where you are at while using the Dremel to remove the white polymer. They do disappear when you are close to the bottom and at that point it is important to take your time and watch for the final layer of white polymer to give way to the colored polymer below.

Above you can see that there are a lot of shavings from removing the white polymer. If you have access to a shop vac I highly suggest rigging it so that it will aide in the removal of the shavings while you are working.

As you get further down and the walls of the white polymer become thinner you can actually use a set of pliers to remove it.

Above you can see that the white polymer has given way to the black polymer below. You will also notice that the trigger hole will need to be milled/dremeled out to allow for the trigger to fit in. When you do this be careful not to remove too much or it will be possible for your springs to fall through the hole.

When drilling the holes for the trigger and hammer pins I highly suggest drilling straight through from one side to the other. The directions on EP Lowers site say to do them one side at a time, which I did and because I was doing it by hand the drill walked and ended up miss drilling the holes (this was my fault). I ended up with the left side holes sitting lower than the right side, and this lead to the hammer being off center, which lead to the trigger not releasing it. 

Also my selector hole was off, it still worked but was extremely stiff due to it being angled.

Even though I miss drilled the holes I was able to fill them with epoxy (double bubble extra strength epoxy) and drill from the right hand side. This straightened out the issues and will be strong enough to hold the pins and selector in place (however I chose to go with KNS anti walk pins just to make sure they won't move).

As for the quality of the lower, I cannot speak on the durability of it yet since I haven't had the opportunity to toss an upper on it and run it to the range; but it does have a solid feel. It has very little give compared to some of the other polymer lowers I have messed with before and the polymer has a nice feel to it. The "finish" of the polymer is clean and some people who have seen the pictures of the lower have actually mistaken it for a billet lower. 

Once I have a few hundred rounds on it at the range I will be writing a follow up post along with some videos of it performing at the range. I have no doubt that it will work just fine and will be a great range rifle.

Overall this was an awesome learning experience, it gave me a whole new appreciation for building a lower. If you like to tinker on your own firearms and are looking for a new project head on over to www.EPLowers.com and check out what they have to offer.

Strike Industries AK TRAX Rail System

I am sure that many of you have seen the video on the Strike Industries AK TRAX hand guard that I posted earlier in the week, for those of you who haven't I have imbedded it below.

I have been extremely happy with this hand guard so far, but then again the standard Saiga hand guard leaves you with absolutely no mounting options and honestly it looks just a bit weird since they "sporterized" it. So having the option to put a hand guard on that has quite a few different ways to mount rails is pretty awesome.

There are quite a few things to like about the AK TRAX, from the key mod rail system to the multiple mounting options for the hand guard itself. The overall quality is really good, there aren't any rough or sharp "unfinished" spots to be found, and the finish is also great quality.

So far I have had it on my AK for around 2 months and have used it on the range quite a few times, I figure it has been on for around 1,000 rounds so far. Like I mentioned in the video I did have an issue with the front mounting screws falling out because I didn't loctite them in place, but that was an easy fix thanks to the awesome customer service over at SI. Other than the one hiccup with losing the small screws there have been absolutely no other issues with this hand guard, the key mod rails mount nice and snug to it and do not loosen up during use; it has been great having the ability to run a flashlight and the gopro on the rifle.

If you are looking for a good hand guard to install onto your AK I would highly suggest taking a look at the info at www.StrikeIndustries.com.

I will be posting follow up reviews as time goes on so make sure to check back!

Lantac Dragon Compensator

Lantac USA recently announced the release of their Dragon Compensator for 5.56/.223 with plans to release a 30Cal version in the near future. They have done a great deal of hyping for the release of the 5.56 Dragon comp, so the question in my mind was "does it meet all of the hype?", and of course the only way to find out was to get my hands on one and take it out for some range time.

SPECIFICATION:

Caliber: 5.56X45mm / .223

Material: Super Hard Milspec Steel

Finish: Nitride QPQ

Dimensions: L: 2.570'', DIA: .870''

Weight: 3.2oz

Thread: 1/2-28 UNEF R/H

Serial Numbered for Quality Control

Made in the USA.

When you first catch sight of this compensator you immediately see a resemblance to the muzzle device of an AK-74, with the 4 top ports and the 3 sleek open ports on either side of it. It is one extremely nice looking compensator that just seems to scream that not only does it look good but it will perform just as nicely as it looks.

As soon as it was installed on the S&W M&P AR-15 the range began to call out to it, and once it was out on the range it answered that call.

Out of the handful of different compensators I have shot with over the past couple of years my biggest complaint was that each one of them when being used under the range cover rattled my brains and made my sinuses hurt. However this was not the case with the Lantac Dragon, instead of forcing the majority of the concussive force upwards in an effort to keep the muzzle down the majority of the concussive force was pushed foward and away from the shooter. This resulted in a much more pleasant shooting experience when under the range cover. 

Now even though the majority of the force is pushed out the sides and forward, it doesn't mean that the compensator was not effective at doing its job of keeping the muzzle from rising. Instead this was one of the flattest shooting compensators I have used, there was literally no muzzle rise after each shot; and to top it off the amount of felt recoil was also reduced. Pair the lack of muzzle rise with the reduced feel of recoil and you have the ability to quickly aquire your target.

At 100 yards using a Lucid Red Dot I was able to continually smack the 10" metal gong, and double taps were amazingly easy to control and still ring the gong. It brought a sense of controllability I have been looking for when it comes to using an AR and firing quickly.

Overall I was extremely impressed with the performance of the Dragon Compensator and cannot wait to get my hands on one for each of the AR builds that I am currently working on. 

If you have been looking for a great compensator to slap onto your AR, this is one that I highly suggest you look into.

You can preorder one through Harris Tactical using the following link.

http://www.harristacticalonline.com/Lantac-Dragon-556-Muzzle-Brake-LAN-DGN556B.htm

Iron Hammer Armory .300 Blackout Upper Review

A couple months back I started talking with Iron Hammer Armory about the AK's that they have been producing and also the line of AR's that they have been working on putting out. There have been a lot of conversations between Martin and myself and I have come to really appreciate the information that I get from him whenever I ask questions. So when I was asked if I would be up for testing and reviewing the IHA .300BLK complete upper I told them heck yes, I would love to get my hands on any AR upper to take out and test anytime I can.

When I picked up the upper from a friend's shop I was really impressed with the way that it looked, with the Stainless Steel Barrel coming out from under a black hand guard it has such a cool look to it. What I thought was really awesome was that the Hand Guard was from ODIN Works which is another company whose products I have heard great things about and had hoped at some point I would get to check out in person.

While I personally prefer a longer hand guard on my AR uppers the 9.5" that the IHA is outfitted with does give it a very clean look since it allows the SS barrel to really stand out. I took some time to field strip the upper and give it a good cleaning and applied FIREClean to it like I do with all of my other firearms (yes even when I do testing for companies I still give it a good clean before and after shooting), this gave me the chance to check out the workmanship that has gone into the building of this upper.

First thing that I noticed was that there was not a single blemish to be found inside and out, and the BCG was staked correctly and everything fit together really well. It was very noticeable that there was great pride taken in assembling the upper. The laser etching on the receiver and the charging handle is a very nice touch and adds some character to the overall build also.

The ODIN Works hand guard is very sleek and very comfortable to hold since it is smooth on the sides with one small section of rail on the bottom side at the front. The rail matches up perfectly with the receiver and gives it a nice continuous look. The overall construction of the ODIN Works hand guard is really good, while being lightweight it did not feel cheap or flimsy like it could break at any second. Just from the short amount of time that I have had with it I have decided I will be using one of their longer hand guards on one of my future builds.

When I was able to take the upper out to the range it was both too windy and too busy for me to be able to setup the cameras to capture any good videos of me firing it, there was also the issue of the wind blowing down the target stand that I was trying to use to zero it in. So finally I gave up and just aimed for the steel plate that we had setup down range. Even though the scope I was using was garbage I was able to figure out where to place the reticle to ring the steel, and once that was figured out I can tell you the steel just kept ringing. 

Every shot that I was sending down range was hitting it's intended spot, and even though I did not have a paper target to measure exactly how accurate this upper is, the side by side and stacked marks on the steel were enough for me to consider this an accurate barrel and with a properly sighted scope and a worked up hand load it should be hitting Sub MOA (I am not an expert marksman but I have shot both well made and crappy made barrels and this is well made). 

While the price for the upper is still up in the air until IHA is able to get the production of them moving I will say that it is a very nice upper with some very nice features, I am sure that the price will contend with many of the other companies that are building uppers, and even if it is a little higher the quality and craftsmanship that is put into it shows. Below you will find a graphic that has the breakdown of the parts used for this upper, all of the parts are nice quality parts that should give you a long happy service life from it.

I would like to thank Martin at Iron Hammer Armory for allowing me the opportunity to take this upper out to the range and check it out, this was the first time that I have been able to test a new product for a company before it's release and I am hoping that I will get the opportunity to do that more often.

Kies Adjustable Gas Block

There were quite a few different gas blocks that I had looked at when I started ordering parts for the Spartan build. I had decided that this build I wanted to do an adjustable gas block so I could really fine tune the rifle, and if sometime in the future I picked up a suppressor I would be able to adjust the settings to make the rifle function properly.

The Kies Firearms Adjustable Gas Block caught my eye when I was browsing through the parts section on Joe Bob Outfitters, it was in the price range that I was looking to spend and it had some pretty decent reviews on it. Oh and for those of you who have done gas rails before and hate the roll pin as much as I do, the Kies gas block uses an allen screw in it's place.

Being that I was using the the Midwest Industries Gen-2 SS hand guard I knew that the inner diameter was smaller than the normal hand guards that are out there and I was a little concerned that the two pieces wouldn't work together. So I contacted Joe Bob Outfitters and asked if they knew if the two would be compatible, and as always I received a quick response with a for sure answer that they would and I was good to go with my order.

When the package arrived 2 days later (I have always appreciated Joe Bob's quick shipping!) I pulled out all of the individual parts that I had ordered and checked them over to make sure that everything was there and nothing was damaged. When I came to the Kies gas block I checked it over really well and was very impressed with the quality and finish of it, especially for the lower end price tag that it had on it.

Installing it onto to my Rainier barrel was really easy, unlike some other blocks I have used in the past this one did not require any tapping with the brass hammer to get it into place. Another thing that I really liked about it was the allen set screw that was included to be used in place of the roll pin, let me tell you all this now, it is one of the smallest set screws I have ever messed with so be careful not to lose it if you get this gas block. Running the set screw in was probably one of the easiest things I did on this entire build, and once it's in it is not coming out. My Rainier barrel has a divot for where the set screw should set for the gas block, which made it very easy to get it into position and properly secured.

The first time I took the rifle out to the range I had to make the initial adjustment to the gas block, and the only problem I had was that the set screw for adjustments was behind my hand guard and there is no way to adjust it without removing the hand guard. Not really that big of a deal with as easy as the hand guard is to remove.

The first shot that I took the set screw was all the way in, the rifle fired but did not cycle which was expected. I backed the set screw out a turn and fired, the bolt cycled but only part of the way and did not lock back on the empty magazine. Again I made an adjustment but this time I took it out 3 turns, which was too much and slapped the bolt forward. At this point I was trying to figure out exactly how many turns I needed to go in, so I bottomed it out again and took it out 2 and a quarter turn, this was the ticket, everything functioned as advertised except for the ejector (which I discussed in the RGuns BCG post).

Since the first trip out I have run somewhere around 400 rounds down range with the rifle and have not had a single hiccup out of it. All of the set screws for the Kies Gas Block are still tight and in position, and I am looking forward to seeing how much abuse I can actually put this block through once ammo becomes available and affordable again.

If you are looking for a budget adjustable gas block make sure to add the Kies gas block to your list, I am happy with it so far and I will definitely use one on the .300 Blackout build I plan to do in the future.